Roll Up Grille
Loading...
Aluminum Roll up Security Grilles and Closures.
We manufacture rolling closures and security grilles that provide security for storefront and office entrances. We fabricate custom roll up grilles to meet your door requirements.
Rolling Grilles provide access control and off hour security on interior and exterior openings.Rollup grilles as access control, for your safety, elegant design, with great ventilation area. protection with transparency.We install rolling security grilles for malls, grocery/drug stores, schools, stadiums, hotels and airports across North America.Our crisp, clean lines of an Rollup grille will make your security solution an aesthetically pleasing one.
Features
- Roll-guard model is Open Style security rolling grille.
- Made of Sturdy aluminum extrusions and continuous metal rods assembled in a open style pattern.
- Roll-guard security grille protects against theft and vandalism.
- Roll-guard rolling grille provide protection against break-ins without restricting air flow or visibility.
- Roll-Guard features reinforcement tubes with just 7/8" (22 mm) spacing between the rods therby making it the most secure rolling grille.
- Unique alternative to traditional rolling and counter security grilles.
- It’s the logical choice for storefronts, display windows, airports, stadiums, and more.
- Suitable for any public building where ventilation and maximum security are required.
- Roll-Guard (open style, closer rods & links) model constructed of 1 1⁄4" (32mm) high on center horizontal sections of full width concealed 5/16” (8mm) diameter rods spaced at 9” (230mm) intervals by 5/8” (16mm) x 3 1/8” (79mm) vertical links. All horizontal rods are covered by 7/16" (11mm) diameter aluminum horizontal spacer tubes leaving 7/8" (22mm) spacing between tubes.Material: Standard aluminum 6063-T5 shall be clear anodized finish.
- End Plates: 3/16 " thick End plates to support the ends of the barrel assembly with sealed, self-aligning shaft bearings. End plates bolted to support tubes.
- Guides: Vertical curtain guides are to be of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Good-looking roll-up door for high-end storefronts and any location with a contemporary architectural vibe.
- Operation : Manually Operated or Electrically operated or hand chain hoist or hand crank with removable crank
- Closures over 16 feet (4.8 m) wide should be electrically operated.
- Industrial duty, jackshaft hoist type motor use for Rolling Grille.
- Manual Push Up and Down effort to raise or lower the grille shall not exceed 15 pounds (7kg) force.
- Vertical curtain guides are of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Mounting Options: Between the Jamb(recess mount) or Face of Wall (Surface mount)
- Supports: 3” (76mm) X 3” (76mm) structural tubes with 0.120 (3mm) wall thickness. Tubes to be attached to the floor slab and joists above. Attachment at top is for lateral support only. For openings over 250 sqft (2.3m2 ,4” (101mm) X 4” (101mm) structural tubes may require. For face of wall installation, instead of steel tubes, 2” (50mm) X 3” (76mm) steel angles may be used.
- Options for Hood: 2, 3 or 4 sides (please choose) 0.032” (0.8mm) clear anodized hood to cover barrel and rolling grille.
- Optional emergency egress device to disengage motor in case of an emergency.
- Optional Electrical key switch - Flush Mounted for motorized Operation
- Heavy duty extruded aluminum Bottom Bar equipped with two 1” (2.5mm), 5 pin mortise cylinders inside and outside.
Features
- Roll-126 is Open Style rod and links model rolling grille.
- Made of Sturdy aluminum extrusions and continuous metal rods assembled in a open style pattern.
- Protects against theft and vandalism.
- Provide protection against break-ins without restricting air flow or visibility.
- Allowing full view of what’s inside.
- Unique alternative to traditional rolling and counter grilles.
- It’s the logical choice for storefronts, display windows, airports, stadiums, and more.
- Excellent solution for locations requiring security and visual appeal, like high-end stores.
- Roll-126 (open style, rods & links) model constructed of 2 1⁄2” (64mm) high on center horizontal sections of full width, concealed 5/16” (8mm) diameter rods spaced at 9” (230mm) intervals by 5/8” (16mm) x 3 1/8” (79mm) vertical links. All horizontal rods are covered by 7/16" (11mm) diameter aluminum horizontal spacer tubes leaving 2 1⁄4" (57mm) spacing between tubes.
- Material: Standard aluminum 6063-T5 shall be clear anodized finish.
- End Plates: 3/16 " thick End plates to support the ends of the barrel assembly with sealed, self-aligning shaft bearings. End plates bolted to support tubes.
- Guides: Vertical curtain guides are to be of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Good-looking roll-up door for high-end storefronts and any location with a contemporary architectural vibe.
- Operation : Manually Operated or Electrically operated or hand chain hoist or hand crank with removable crank
- Closures over 16 feet (4.8 m) wide should be electrically operated.
- Industrial duty, jackshaft hoist type motor use for Rolling Grille.
- Manual Push Up and Down effort to raise or lower the grille shall not exceed 15 pounds (7kg) force.
- Vertical curtain guides are of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Mounting Options: Between the Jamb(recess mount) or Face of Wall (Surface mount)
- Supports: 3” (76mm) X 3” (76mm) structural tubes with 0.120 (3mm) wall thickness. Tubes to be attached to the floor slab and joists above. Attachment at top is for lateral support only. For openings over 250 sqft (2.3m2 ,4” (101mm) X 4” (101mm) structural tubes may require. For face of wall installation, instead of steel tubes, 2” (50mm) X 3” (76mm) steel angles may be used.
- Options for Hood: 2, 3 or 4 sides (please choose) 0.032” (0.8mm) clear anodized hood to cover barrel and rolling grille.
- Optional emergency egress device to disengage motor in case of an emergency.
- Optional Electrical key switch - Flush Mounted for motorized Operation
- Heavy duty extruded aluminum Bottom Bar equipped with two 1” (2.5mm), 5 pin mortise cylinders inside and outside.
Features
- Roll-99 model is Open Style rolling grille
- Made of Sturdy aluminum extrusions and continuous metal rods assembled in a checkerboard pattern.
- Protects against theft and vandalism.
- Allowing full view of what’s inside.
- Unique alternative to traditional rolling and counter grilles
- Excellent solution for locations requiring security and visual appeal, like high-end stores.
- Roll-99 (open style) model Curtain shall be constructed of 2 1⁄2” (64mm) X 9" (230mm) aluminum slats arranged in a checkerboard pattern. These slats held by 5/16" (8mm) diameter horizontal aluminum rods.
- Material: Standard aluminum 6063-T5 shall be clear anodized finish.
- End Plates: 3/16 " thick End plates to support the ends of the barrel assembly with sealed, self-aligning shaft bearings. End plates bolted to support tubes.
- Good-looking roll-up door for high-end storefronts and any location with a contemporary architectural vibe.
- Operation : Manually Operated or Electrically operated or hand chain hoist or hand crank with removable crank
- Closures over 16 feet (4.8 m) wide should be electrically operated.
- Industrial duty, jackshaft hoist type motor use for Rolling Grille.
- Manual Push Up and Down effort to raise or lower the grille shall not exceed 15 pounds (7kg) force.
- Vertical curtain guides are of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Mounting Options: Between the Jamb(recess mount) or Face of Wall (Surface mount)
- Supports: 3” (76mm) X 3” (76mm) structural tubes with 0.120 (3mm) wall thickness. Tubes to be attached to the floor slab and joists above. Attachment at top is for lateral support only. For openings over 250 sqft (2.3m2 ,4” (101mm) X 4” (101mm) structural tubes may require. For face of wall installation, instead of steel tubes, 2” (50mm) X 3” (76mm) steel angles may be used.
- Options for Hood: 2, 3 or 4 sides (please choose) 0.032” (0.8mm) clear anodized hood to cover barrel and rolling grille.
- Optional emergency egress device to disengage motor in case of an emergency.
- Optional Electrical key switch - Flush Mounted for motorized Operation
- Heavy duty extruded aluminum Bottom Bar equipped with two 1” (2.5mm), 5 pin mortise cylinders inside and outside.
Features
- 50% perforated steel slats covered with high resistance powder coat paint.
- Roll-Air (perforated panels) model constructed of 3” (76mm) on center extruded aluminum sections. Each section framed with continuous, double “C” hinge with 2 1⁄2” (64mm) high 20 gauge .035” (.90mm) perforated metal panels 15” 3⁄4 (400mm) wide.
- Perforated Steel Slats provides excellent airflow and visibility
- Material: Standard aluminum 6063-T5 shall be clear anodized finish.
- End Plates: 3/16 " thick End plates to support the ends of the barrel assembly with sealed, self-aligning shaft bearings. End plates bolted to support tubes.
- Enhance security by perforated panel to prevent hand thru reaching at locks.
- Good-looking roll-up door for high-end storefronts and any location with a contemporary architectural vibe.
- Operation : Manually Operated or Electrically operated or hand chain hoist or hand crank with removable crank
- Closures over 16 feet (4.8 m) wide should be electrically operated.
- Manual Push Up and Down effort to raise or lower the grille shall not exceed 15 pounds (7kg) force.
- Vertical curtain guides are of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Mounting Options: Between the Jamb(recess mount) or Face of Wall (Surface mount)
- Supports: 3” (76mm) X 3” (76mm) structural tubes with 0.120 (3mm) wall thickness. Tubes to be attached to the floor slab and joists above. Attachment at top is for lateral support only. For openings over 250 sqft (2.3m2 ,4” (101mm) X 4” (101mm) structural tubes may require.For face of wall installation ,instead of steel tubes , 2” (50mm) X 3” (76mm) steel angles may be used.
- Options for Hood: 2, 3 or 4 sides (please choose) 0.032” (0.8mm) clear anodized hood to cover barrel and rolling grille.
- Optional emergency egress device to disengage motor in case of an emergency.
- Optional Electrical key switch - Flush Mounted for motorized Operation
- Heavy duty extruded aluminum Bottom Bar equipped with two 1” (2.5mm), 5 pin mortise cylinders inside and outside.
Features
- Roll-Vision model with transparent polycarbonate insert.
- Protects against theft.
- Keeps out debris while allowing full view of what’s inside.
- Excellent solution for locations requiring security and visual appeal, like high-end stores.
- Roll-Vision (clear polycarbonate) model constructed of 3” (76mm) on center extruded aluminum sections. Each section framed with continuous double “C” hinge with 2 1⁄2” (64mm) high 1/16” (1.5mm) thick clear polycarbonate panels 15” 3⁄4 (400mm) wide.
- Clear Polycarbonate Slats provides excellent visibility
- Material: Standard aluminum 6063-T5 shall be clear anodized finish.
- End Plates: 3/16 " thick End plates to support the ends of the barrel assembly with sealed, self-aligning shaft bearings. End plates bolted to support tubes.
- Enhance security by polycarbonate insert to prevent hand thru reaching at locks.
- Good-looking roll-up door for high-end storefronts and any location with a contemporary architectural vibe.
- Operation : Manually Operated or Electrically operated or hand chain hoist or hand crank with removable crank
- Closures over 16 feet (4.8 m) wide should be electrically operated.
- Industrial duty, jackshaft hoist type motor use for Rolling Grille.
- Manual Push Up and Down effort to raise or lower the grille shall not exceed 15 pounds (7kg) force.
- Vertical curtain guides are of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Mounting Options: Between the Jamb(recess mount) or Face of Wall (Surface mount)
- Supports: 3” (76mm) X 3” (76mm) structural tubes with 0.120 (3mm) wall thickness. Tubes to be attached to the floor slab and joists above. Attachment at top is for lateral support only. For openings over 250 sqft (2.3m2 ,4” (101mm) X 4” (101mm) structural tubes may require. For face of wall installation, instead of steel tubes, 2” (50mm) X 3” (76mm) steel angles may be used.
- Options for Hood: 2, 3 or 4 sides (please choose) 0.032” (0.8mm) clear anodized hood to cover barrel and rolling grille.
- Optional emergency egress device to disengage motor in case of an emergency.
- Optional Electrical key switch - Flush Mounted for motorized Operation
- Heavy duty extruded aluminum Bottom Bar equipped with two 1” (2.5mm), 5 pin mortise cylinders inside and outside.
Features
- Open Style Rolling Grille
- Without polycarbonates inserts but same look and security as Roll-vision model
- High security protection with open style design
- Ideal Security Rolling Grille for window, door,counter and other security protection
- Protects from vandalism and theft
- Constructed of 3” (76mm) on center extruded aluminium sections. Each section framed by continuous double “C” hinge hold 2 1⁄2” (64mm) high x 0,050” (1,3mm) aluminum slats leaving 15 3⁄4" (400mm) X 2 1⁄2" (64mm) open spaces in a straight pattern.
- Header End plate is made of 3/16” (4.7mm) thick.
- Header End Plate size varies with the height of grille.
- Guides: Vertical curtain guides are to be of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Good-looking roll-up door for high-end storefronts and any location with a contemporary architectural vibe.
- Operation : Manually Operated or Electrically operated or hand chain hoist or hand crank with removable crank
- Closures over 16 feet (4.8 m) wide should be electrically operated.
- Industrial duty, jackshaft hoist type motor use for Rolling Grille.
- Manual Push Up and Down effort to raise or lower the grille shall not exceed 15 pounds (7kg) force.
- Vertical curtain guides are of extruded aluminum 1 3⁄4” (4.4mm) wide x 2 1⁄2” (6.4mm) deep with nylon brush seal to allow smooth operation.
- Mounting Options: Between the Jamb(recess mount) or Face of Wall (Surface mount)
- Supports: 3” (76mm) X 3” (76mm) structural tubes with 0.120 (3mm) wall thickness. Tubes to be attached to the floor slab and joists above. Attachment at top is for lateral support only. For openings over 250 sqft (2.3m2 ,4” (101mm) X 4” (101mm) structural tubes may require. For face of wall installation, instead of steel tubes, 2” (50mm) X 3” (76mm) steel angles may be used.
- Options for Hood: 2, 3 or 4 sides (please choose) 0.032” (0.8mm) clear anodized hood to cover barrel and rolling grille.
- Optional emergency egress device to disengage motor in case of an emergency.
- Optional Electrical key switch - Flush Mounted for motorized Operation
- Heavy duty extruded aluminium Bottom Bar equipped with two 1” (2.5mm), 5 pin mortise cylinders inside and outside.
GLASSESSENTIAL® Rolling Security Grille has various models requiring different mounting options.
Steel Support Tubes
- Tubes are mounted into a sleeve cup on the slab and attached to the steel joints at the top.
- This allows for the grille/closure to be installed first before any walls are built.
- This eliminates the difficulty of working around studs, HVAC and plumbing.
- Tubes can be bought from us or acquired locally saving shipping costs
“L” Angle Face of Wall Mount
- Guides and Counter Balance Assembly can be supported by steel or aluminum angles.
- When the jamb is steel-capped, the angle faces toward the opening, known as E - Mount.
- When the jamb is wooden, the angle faces away from the opening, known as Z - Mount.